Model 625 Features and Specifications

Precision machined from a single block of non-resonant aircraft aluminum, the Model 625 features a unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback.

Virtually free from EMI field contamination and mechanical vibration, the Model 625 delivers a sensuous grain-free musicality of unparalleled transparency and low level resolution that emerges from a rich velvety background.


TECHNICAL FEATURES

Machined Aluminum Chassis
Precision-machined chassis with integrated heat sinks, milled from a solid block of aircraft grade aluminum, provides exceptional thermal heat transfer/dissipation, RFI/EMI shielding, and resonance control.

Composite Circuit Architecture
Unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback, delivers a sensuous grain-free musicality of unparalleled transparency and low level resolution.

Balanced Topology
Inherent cancellation effects of balanced topology implemented throughout all power and input/output circuits ensures greatly reduced distortion and noise under dynamic signal conditions.

High Current Copper Bus-bars
High current, dual polarity, ultra low impedance copper bus-bars distribute both power supply input current and signal output current, virtually eliminating intra-circuit EMI signal contamination, greatly reducing internal wiring, while increasing circuit board rigidity.

High-Precision Surface Mount Components
Extensive use of Lead (Pb)-free, low temperature coefficient, active and passive surface-mount components results in significantly smaller loop areas, reduced circuit capacitance and inductance, and introduces less noise than conventional leaded components.

Transformer-Coupling and Isolation
Transformer coupled input circuitry provides universal component compatibility and virtually eliminate ground loop noise and RFI/EMI. Transformer coupling ensures identical amplifier overall gain when using unbalanced input adapters.

Power Factor Correction
Power Factor Correction (PFC) in the power supply reduces AC line harmonic noise pollution and increases AC line power utilization to 99%.

High-Efficiency Switch-Mode Power Supply
Highly efficient, compact, light weight, 1500 watt DC switch-mode power supply provides optimum voltage regulation for all circuits and operating conditions, and allows for quiet operation over a wide range of AC mains power sources.

Dual-Position Speaker Terminals
Dual CE approved speaker output terminals, in both horizontal and vertical orientation, require no tools for secure, low resistance connections, and allow for easy bi-wiring applications.

Flexible 20 amp AC Power
20 amp AC power inlet accepts a wide variety of after-market high-performance power cables.

Front Panel Standby Button
Illuminated front panel push-button switches the amplifier into standby mode (< 1 watt consumption).

Rear Panel Remote Jack
12V 3.5mm jack on rear panel permits amplifier power on/standby switching in remote and home theater applications.

Self-Leveling Supports
Removable 3-point self-leveling Delron chassis supports provide high frequency  mechanical noise isolation.


SPECIFICATIONS

Output Power    
300 watts @ 8 ohms / 550 watts @ 4 ohms

Frequency Response   
5 Hz – 350 kHz

S/N Ratio   
95 dB, ref. 1.0 watt @ 8 ohm load

Output Noise   
< 55 µv, 20 Hz – 20 kHz, unweighted

Crosstalk   
> 91 dB @ 1 kHz, 74 dB @ 20 kHz

Input Impedance   
10k ohms

THD + Noise   
0.005% @ 1 kHz, 8 ohms

Damping Factor   
> 200,  20 Hz - 20 kHz

Overall Gain (Balanced or Unbalanced)   
27 dB

Common Mode Rejection Ratio   
> 90 dB, 20 Hz – 20 kHz

Absolute Phase Non-inverting   
Pin 2 Positive

Inputs   
1 pair balanced (XLR)

Outputs   
2 pair parallel binding posts per channel

Power Consumption Idle   
100 watts

Power Consumption Standby   
1 watt

Amplifier Weight   
54 lbs. / 24.5 kg

Amplifier Shipping Weight   
64 lbs. / 29 kg

Overall Amplifier Dimensions (h/w/d)   
5.75” x 15.5” x 16.25” / 146mm x 394mm x 413mm


Related Articles

Attachments

Visitor Comments

Article Details

Last Updated
25th of September, 2013

Would you like to...

Print this page  Print this page

Email this page  Email this page

Post a comment  Post a comment

 Subscribe me

Subscribe me  Add to favorites

Remove Highlighting Remove Highlighting

Edit this Article

Quick Edit

Export to PDF


User Opinions



How would you rate this answer?




Thank you for rating this answer.

Continue