Continuum S2 Integrated Features and Specifications

Featuring enhanced sonic performance and flexibility, the new Rowland Continuum Series 2 integrated amplifier delivers stunning dynamic realism and expressive refinement through advanced topologies. Continuum S2 integrates the new Capri S2 preamplification circuit, input/output, and control features with an innovative 400-Watt power amplification stage into a single chassis.

The amplifier delivers the trademark Rowland musicality, resolution, and unfailing authority to the most refined audio environments. Challenge Continuum S2 to the extreme dynamics of high-resolution digital sources and the power requirements of large bi-wired speakers. Apply it to the complex loads of electrostatic panels in analog rigs. Admire its exceptional realism driving single-wired studio monitors in a sophisticated multi-media system.

The elegance of Continuum S2’s ergonomic console emerges from a solid block of aircraft-grade aluminum. Discover the impressive complement of standard input/output interfaces. Enhance its flexibility through the optional DAC card, or its fully redesigned phono stage.

TECHNICAL FEATURES

Compact elegance
Balanced integrated amplifier design housed inside a low profile, compact, ultra-low resonance, structurally rigid chassis that is precision-machined from solid blocks of aircraft grade 6061-T6 aluminum that is completely sealed for trouble-free operation and high RF and EMI isolation. A separate pocket is milled within the chassis to enclose a low noise, auto-ranging switch-mode power supply which accepts all world-wide mains voltages.

I/O flexibility
Dual low impedance line-level outputs (80 Ohms balanced, 40 Ohms unbalanced), 48 Ohms balanced and unbalanced inputs, and preamp bypass inputs allow unprecedented compatibility with audio and A/V components.

High-precision surface mount components
Extensive use of Lead (Pb)-free, low temperature coefficient, active and passive surface-mount components results in significantly smaller loop areas, reduced circuit capacitance and inductance, and introduces less noise than conventional leaded components.

Thin-film resistors
All resistors are low noise, 0.1% thin-film type for extremely low thermal noise which complement the low-noise characteristics of the active circuitry.

Four-layer circuit board
All circuitry is populated on one side of a 4 layer circuit board to allow for continuous, unbroken, low impedance ground and power supply distribution planes. Care was taken to minimize signal path lengths and components sizes.

Input transformer-coupling and isolation
Transformer coupled input circuitry provides universal component compatibility and virtually eliminate ground loop noise and RFI/EMI. Transformer coupling ensures identical overall gain from all inputs. Other benefits include ground noise isolation and excellent common mode noise rejection (CMRR) from all sources.

Precision volume adjustments
Dual rate volume control allows precision level adjustments over nearly a 100 dB range. The volume control incorporates a permanently noiseless optical encoder that always maintain its tactile feel, accuracy, and channel balance at all settings. The optical encoder mounted behind the volume knob commands the attenuation level of a monolithic resistor attenuator over a 99.5 dB range in 0.5 dB increments. Excellent channel matching, monotonicity, and low noise is achieved throughout the entire volume adjustment range over the lifetime of the product.

High-efficiency switch-mode power supply
Highly efficient, compact, light weight, switch-mode power supply provides optimum voltage regulation for all circuits and operating conditions, and allows for quiet operation over a wide range of AC mains power sources.

Optional phono card
Plug-in phono cards (installed internally) converts Line Input 1 to high performance phono input. Three gain and loading options can accommodate moving magnet (MM), moving coil (MC), and high output moving coil cartridge types.

Optional DAC card
Plug-in DAC card (installed internally) converts Line Input 1 to high performance DAC input. Accepts all SPDIF digital signal sources from 44.1 to 192 kHz sampling rates and adjusts accordingly.

Home theatre bypass adjustment
The Home Theatre BYPASS RCA inputs can be changed to an additional set of standard inputs by placement of an internal jumper inside the unit.

Display off (5 sec)
An internal jumper will place the display in an automatic OFF condition after 5 seconds from any operational command and illuminates again for 5 seconds after additional commands are initiated.

Remote control
Six-function remote control transmitter adjusts volume, input selection, mute, channel balance with display, display dimming and turn-off, and control of absolute phase.
 
High-quality connectors
All signal connectors are rhodium plated, copper jacks (RCA) and Neutrix silver plated contact (XLR), soldered directly to the circuit board for direct connection to the signal circuitry.

Green technology
Modest power consumption permits constant power-up operation to eliminate warm-up time and maximize musical performance, and allows Continuum S2 Preamplifier to operate enclosed into an entertainment unit.

IEC
15 Amp female IEC AC power connector.

SPECIFICATIONS

Output Power
400 watts @ 8 ohms/800 watts @ 4 ohms

Frequency Response
5 Hz - 70 kHz, -3 dB @ 8 ohms

Inputs
2 pair balanced (XLR)
2 pair unbalanced (RCA)
1 pair unbalanced bypass (RCA)

Outputs
1 pair balanced (XLR)
1 pair unbalanced (RCA)
1 pair CE-Approved Speaker Wire Clamp

Weight
35 lb / 15.9 kg

Dimensions (H/W/D)
5.3" x 15.5" x 15.0"
135mm x 394mm x 380mm


Related Articles

Attachments

No attachments were found.

Visitor Comments

Article Details

Last Updated
25th of September, 2013

Would you like to...

Print this page  Print this page

Email this page  Email this page

Post a comment  Post a comment

 Subscribe me

Subscribe me  Add to favorites

Remove Highlighting Remove Highlighting

Edit this Article

Quick Edit

Export to PDF


User Opinions



How would you rate this answer?




Thank you for rating this answer.

Continue