Model 725

  • Model 725 Monoblocks

    Features a unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback.

  • img
  • img
  • img
  • img
 
 

Model 725 Features

Machined Aluminum Chassis

Precision-machined chassis with integrated heatsinks, milled from a solid block of aircraft grade 6061-T6 aluminum, provides exceptional thermal heat transfer/dissipation, RFI/EMI shielding, and resonance control.

Ceramic Circuit Boards

All audio circuits are implemented on mil-spec, multi-layer, low dielectric constant, Rogers™ ultra-rigid ceramic circuit board substrate for extremely low energy retention and absorption. Large low impedance ground plane areas for extended internal star-grounding.

Balanced Topology

Inherent cancellation effects of balanced topology implemented throughout all power and input/output circuits ensures greatly reduced distortion and noise under dynamic signal conditions.

High Current Copper Bus-bars

High current, dual polarity, ultra low impedance copper bus-bars distribute both power supply input current and signal output current, virtually eliminating intra-circuit EMI signal contamination, greatly reducing internal wiring, while increasing circuit board rigidity.

High-Precision Surface Mount Components

Extensive use of Lead (Pb)-free, low temperature coefficient, active and passive surface-mount components results in significantly smaller loop areas, reduced circuit capacitance and inductance, and introduces less noise than conventional leaded components.

Transformer-Coupling and Isolation

Transformer coupled input circuitry provides universal component compatibility and virtually eliminate ground loop noise and RFI/EMI. Transformer coupling ensures identical amplifier overall gain when using unbalanced input adapters.

Power Factor Correction

Power Factor Correction (PFC) in the power supply reduces AC line harmonic noise pollution and increases AC line power utilization to 99%.

High-Efficiency Switch-Mode Power Supply

Highly efficient, compact, light weight, 1500 watt DC switch-mode power supply provides optimum voltage regulation for all circuits and operating conditions, and allows for quiet operation over a wide range of AC mains power sources.

Parallel Binding Posts

Dual CE approved speaker output terminals require no tools for secure, low resistance connections, and allow for easy bi-wiring applications.

Flexible 20 amp AC Power

20 amp AC power inlet accepts a wide variety of after-market high-performance power cables.

Front Panel Standby Button

Illuminated front panel push-button switches the amplifier into standby mode (< 1 watt consumption).

Rear Panel Remote Jack

12V 3.5mm jack on rear panel permits amplifier power on/standby switching in remote and home theater applications.

Self-Leveling Supports

Removable 3-point self-leveling Delron chassis supports provide high frequency  mechanical noise isolation.

Model 725 Specifications

Output Power 330 watts @ 8 ohms / 650 watts @ 4 ohms
Frequency Response 5 Hz – 350 kHz
S/N Ratio 95 dB, ref. 1.0 watt @ 8 ohm load
Output Noise < 55 µv, 20 Hz – 20 kHz, unweighted
Crosstalk > 91 dB @ 1 kHz, 74 dB @ 20 kHz
Input Impedance 40k ohms
THD + Noise 0.004% @ 1 kHz, 8 ohms
Damping Factor > 200,  20 Hz - 20 kHz
Overall Gain 27 dB
Common Mode Rejection Ratio > 90 dB, 20 Hz – 20 kHz
Absolute Phase Non-inverting Pin 2 Positive
Inputs Balanced (XLR)
Outputs 2 parallel binding posts
Power Consumption Idle 2 parallel binding posts
Power Consumption Idle 85 watts
Power Consumption Standby 1 watt
Amplifier Weight 54 lbs. / 24.5 kg (each)
Amplifier Shipping Weight 64 lbs. / 29 kg (each)
Overall Amplifier Dimensions (h/w/d) 5.75” x 15.5” x 16.25” / 146mm x 394mm x 413mm (each)

Model 725 Monoblocks

Precision machined from two single blocks of non-resonant aircraft aluminum, the Model 725 features a unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback. The Model 725 features mil-spec ceramic circuit boards, high current copper bus bars, a power supply incorporating 4-pole capacitors and power factor correction, combined to deliver a life-like grain-free musicality of breathtaking transparency.

Model 725 Reviews
theaudiobeat.com - September 2013 - by Roy Gregory
hifi-advice.com - August 2013 - by Christiaan Punter
The Absolute Sound #228 - December 2012 - by Robert Harley

Visit our Video Gallery. more

Download Photos. more